They are making a number of good annotation regarding Tools You Need to Install a New Bathtub in general in this post underneath.
Mounting a bath tub isn't specifically brain surgery, yet it does call for strong plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately hard task. If the old tub is easily obtainable, the job can move rapidly; if you have to open up a wall to remove the old tub as well as place the new tub, the job is a lot harder. In either case, the job is within a home handyman's skills, although you will need a helper to move out the old bathtub and set in the new one. See to it you have actually certified yourself for the work and fit attempting it. As opposed to working with a specialist to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you begin. Opportunities are you may need a professional plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your bathroom if you have actually currently bought a new bathtub and also don't need to change the plan of your previous water pipelines.
Your devices as well as material checklist should consist of the following:
Getting ready for the Setup
To start with, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap ports to the bottom of the two taps utilizing 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipes have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Making use of both wood boards under its feet, position the bathtub in the called for position. The wooden boards are useful in evenly spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The next objective is to make sure that the tub is leveled all round. This can be attained by examining the spirit level and changing the feet on the bath tub till the level reviews degree.
To set up faucets, fit all-time low of the outermost flexible faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the same for the other tap.
Activate the supply of water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Fill the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's instruction manual. Tiling and securing around the bath tub needs to wait until the bath tub has actually been used at the very least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in place in between the tap and the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The former kind needs to be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a stiff seal, triggering the water to penetrate the wall surface in between the bath and also the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can split relatively very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent person who reads on A Step-by-Step Guide to Installing a Bathtub, I think sharing that excerpt was really useful. Kindly set aside a second to promote this post if you enjoyed reading it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Visit Site